Zahnaufhellung LED Curing Light Lamp Dental Zahnarzt Polymerisationslampe GYX

EUR 46,41 Sofort-Kaufen, Kostenloser Versand, 30-Tag Rücknahmen, eBay-Käuferschutz
Verkäufer: dentalskysea006 ✉️ (10.606) 99.4%, Artikelstandort: Beijing, CN, Versand nach: WORLDWIDE, Artikelnummer: 226066340892 Zahnaufhellung LED Curing Light Lamp Dental Zahnarzt Polymerisationslampe GYX.

Description Curing Light T4:   T4 curing light adopts the principle of ray radiation to solidify the light-sensitive resin by shooting at it in a short time. This curing light with adjustable working time, working time visual, curing efficiency higher and intelligent zed charging stand. We have two colors for your reference.   Feature:   Four modes of working time: 10,20,30,40 seconds Working modes: Full power The battery can be replaced The optical fiber can be autoclaved to the high temperature and pressure. Automatic shut down function(120s no any operation)   Technical Specifications:   Power supply:``````````````````````````````````````````````Rechargeable Lithium battery Battery voltage and capacity: ``````````````````````` 4.2V/2000mAh Input of adapter:``````````````````````````````````````````100V to 240V~50Hz/60Hz Light intensity: ````````````````````````````````` ```````````1400MW/CM2   Light source:   A. blue ray B. wave length:420nm-480nm   Working condition: A.environment temperature:````````````````````````````````5℃ to 40℃ B.relative humidity:`````````````````````````````````````````````≤80% Consumption power:````````````````````````≤8W Protection type against electrical shock:````````````````Class Ⅱ Protection against electrical shock:```````````````````````type B   Packing list:   1. Main unit x 1 2. Optical fiber x 1 3. Light hood x 1 4. Adaptor x 1  

    Curing Light ST2: Feature: 1. Built-in light meter function 2 Wireless Inductive charging, longer life span 3 Four models to choose (STRONG LOW FLASHING GRADUALLY STRONG) 4 The handle covered by ANS painting 5 Can be used continuously more than 500times     Technology data: Blue-ray illumination: 5W≥1200Mw/CM2 Capability of battery: 2200mA/h 3.7V Input Voltage: AC 110-240V 50-60Hz Wavelength: 420-480nm Light power: 1200-2000mw/cm2 Solidify depth: 5s/3mm Time select: 5, 10,15,20,25,30,35,40 seconds Battery standby time: 90 days   Packing list: 1 Main unit*1 2 Charging base*1 3 AC adaptor*1 4 Light shade*1 5 Light guide*1 6 Whiten tip *1   Curing Light D8:   Features:   1.Brand New High Quality Curing Light. 2.Composes of high power LED, qualified fiber rod. 3. Noiseless; No libration; Generate little heat when working. 4.Low consumption of standby power with thirty days' standby time 5.Large capacity Li-battery can be used for a long one with full charging. 6.Plenty of fiber rods with very reasonable price on sale for your replacement. 7.Wireless/Cordless design without no cable connect to the unit which could be used very conveniently. 8.It adopts the principle of ray radiation to solidify the light-sensitive resin by shooting at it in a short time. 9.Many brands' resin materials can be cured by this curing-light with optional working modes and lighting times.   Technical:   Light source: blue light Wave length: 420nm-480nm Output intensity: 2000mw/cm2 Exposure times for optimal curing: 8s/ 6s/ 4s Power supply: rechargeable Lithium battery 3.7V/2000mAh Input adapter: 100V to 240V~50Hz/60Hz (Available for global users.)Safety kind: Ordinary type B.non—continuous service Ip40.Class   2.   Working condition: environment temperature: 5℃-40℃; relative humidity:≤80% The fiber rod can be autoclaved up to the tempreture134 °C / 273 °F & pressure 0.2Mpa.     Packing List:   Main Unit*1   Light Guide*1  Light Board*1     Charging base*1 100v-240v AC Adapter*1       English Operation Manual*1    Curing Light D6:   Features: HIGH QUALITY Wireless LED Lamp Dental Curing Light 2000mw Orthodontics D5/D6 DENJOY 1. Brand New High Quality Curing Light. 2. Composes of high power LED, qualified fiber rod.3. Noiseless; No libration; Generate little heat when working. 4. Low consumption of standby power with thirty days' standby time 5. Large capacity Li-battery can be used for a long one with full charging. 6. Plenty of fiber rods with very reasonable price on sale for your replacement. 7. Wireless/Cordless design without no cable connect to the unit which could be used very conveniently. 8. It adopts the principle of ray radiation to solidify the light-sensitive resin by shooting at it in a short time. 9. Many brands' resin materials can be cured by this curing-light with optional working modes and lighting times. Technical: 1. Light source: blue light 2. Wave length: 420nm-480nm 3. Output intensity: 1500-2200mW/cm; 7W LED 4. Power supply: rechargeable Lithium battery 3.7V/2000mAh 5. Input adapter: 100V to 240V~50Hz/60Hz (Available for global users.)6. Safety kind: Ordinary type B.non—continuous service Ip40.Class 2. 7. Working condition: environment temperature: 5℃-40℃; relative humidity:≤80% 8. The fiber rod can be autoclaved up to the tempreture134 °C / 273 °F & pressure 0.2Mpa. 9. Build-in light meter within the base    10. Digital LED screen display, clear operation. 11. BEEP at each 5-seconds to indicate remaining curing time 12. Various Curing Time: seven preset curing time 5/10/15/20/25/30/40 seconds.  13. Three Preset Programs:    a. Fast mode: Full power all the time    b. Soft 1 mode: Generally increasing power in first 5 seconds, then full power till the end.    c. Soft 2 mode: Generally increasing power in first 5 seconds, then half power till the end. 14. Full supply of power can satisfy 10-second curing time for 200 times. 15. When running out of the battery, the unit can be operated directly with the switching power adapter. 16.Suit for Windows XP /Windows Vista/Windows7 32 bit System PC Standard accessory include:  Main Unit   Light Guide Light Board Charging base 100v-240v AC Adapter   English Operation Manual   Curing Light D5:   Features:   1. Brand New High Quality Curing Light. 2. Composes of high power LED, qualified fiber rod.  3. Noiseless; No libration; Generate little heat when working. 4. Low consumption of standby power with thirty days' standby time 5. Large capacity Li-battery can be used for a long one with full charging. 6. Plenty of fiber rods with very reasonable price on sale for your replacement. 7. Wireless/Cordless design without no cable connect to the unit which could be used very conveniently. 8. It adopts the principle of ray radiation to solidify the light-sensitive resin by shooting at it in a short time. 9. Many brands' resin materials can be cured by this curing-light with optional working modes and lighting times.     Technical:   1. Light source: blue light 2. Wave length: 420nm-480nm  3. Output intensity: 1100-1600mW/cm2; 5W LED 4. Power supply: rechargeable Lithium battery 3.7V/2000mAh 5. Input adapter: 100V to 240V~50Hz/60Hz (Available for global users.)  6. Safety kind: Ordinary type B.non—continuous service Ip40.Class 2. 7. Working condition: environment temperature: 5℃-40℃; relative humidity:≤80% 8. The fiber rod can be autoclaved up to the tempreture134 °C / 273 °F & pressure 0.2Mpa. 9. Build-in light meter within the base    10. Digital LED screen display, clear operation. 11. BEEP at each 5-seconds to indicate remaining curing time 12. Various Curing Time: seven preset curing time 5/10/15/20/25/30/40 seconds.  13. Three Preset Programs:    a. Fast mode: Full power all the time    b. Soft 1 mode: Generally increasing power in first 5 seconds, then full power till the end.    c. Soft 2 mode: Generally increasing power in first 5 seconds, then half power till the end. 14. Full supply of power can satisfy 10-second curing time for 200 times. 15. When running out of the battery, the unit can be operated directly with the switching power adapter.     Packing List:   Main Unit*1 Light Guide*1 Light Board*1 Charging base*1 100v-240v AC Adapter*1  English Operation Manual*1   Curing Light 1 Second:  

Model : CV-215-I

A new advanced cordless LED curing light.

It can provide the maximum light intensity safely and consistently.

Features:

- With the high intensity of 2,200 mW/cm

- Wave length Range : 390nm ~ 470nm

- Full coverage for all optical meterials

- Aviation-grade metal body for better heat dissipation

- Wireless fast charging mode with indicator

- Provide light intensity test for secure use

- Three modes for option . P1(1~3s) P2(5~20s)P3(10-20s)

- Automatic power off, low battery alert

Principle and usage:

CV-215-I adopts the principle of ray radiation light-sensitive resin by shooting at it in a short time.

 Technical specifications:

Dimensions: 25mm x 224 mm

Net weight: 193 g

Power source:

1.Power supply: rechargeable Lithium battery

2.Battery mode: ICR 18490

3.Battery voltage and capacity: 3. 7V/2000mA

  Battery has protection against Over-voltage, over-current and short circuit

  Power Input: AC 100V-240V, 50HZ/60Hz

  Input Power: IOVA

  Power Output: DC5V/IA

Light source: 

1.10w high power blue light LED

2.Checking method: the LED light is fine when the light is on during correctly

3.The wave length of this product can match with the clinical dental resin solidification, such as 3M, Dentsply etc

4.Wave length: 380nm-470nm

Light intensity:  1600 mW/cm2-2200mW/cm

Working condition:

1 Environment temperature: +10C to +40C

2 Relative humidity: 30%-75%

3 Atmosphere pressure: 70kPa to106kPa

Equipment safety

1.Operating mode: intermittent operation

2.Protection type against electrical shock: class II

3.Protection degree against electrical shock: type B

4.Protection against harmful ingress of water or particular matter: rdinary equipment(IPXO)

5.Safety in the presence of flammable anesthetic mixture with air, oxygen or nitrous oxide: not suitable under this condition

Install and uninstall way:

1.The top of the unit can be turned 360 degrees to both left and right

while it is forbidden to remove

2.When the battery needs to be charged, connect the plug of the adapter into the AC100V--240V power supply. Then connect the output plug of  the adapter to the DC 5 0V input plug of the pedestal, then put the main  unit into the pedestal

Operation:

Press the mode button. Following two modes are available

  1. Long press P/T button can exchange PI and P2 mode. when it shows P1 01, tap button to P1 03, Long press to model P2  (5S,10S,15S,20S)

2 During the operation, put the disposable sleeve on the top of the main unit, aim the top at the correct position, press the ON/OFF button  and the main unit will produce"Bi"sound, the curing light radiates  blue light and starts working according to the set modes. Meanwhile, it  starts counting down and will produce tone at every 5 seconds, it stops  working when counting down to 0

3 During operation, the blue light can be stopped by press the power button at any time

4 After a working cycle, operator can press the ON/OFF switch to start another working cycle. Stop operating if the equipment began to  heat obviously, do not restart until the equipment cool down. Sugges  continues working cycle less than 10 times

5 Low power detective circuit is fixed inside of the main unit, when low power is detected, the display screen of main unit will wink, please  charge in time

6 When the battery needs to be charged, connect the plug of the adapter into the AC100V-240V power supply. Then connect the output plug  of the adapter to the DC 5.0V input plug of the pedestal, and then the  logo turn to blue. Put the main unit to the charging point of the pedestal  the display screen turn to scrolling display, and the curing lights starts  charging

7 After operating, take off the disposable sleeve and throw away, forbidden to reuse

8 This equipment will turn off automatically if don t any action within 2 minutes, turn it on by press any button

9 The depth of solidification of composite is no less than 2mm per I second

Precaution:

1 Please recharge the battery at least 4 hours before first time usage

2 In order to prevent cross-infection, it is forbidden to reuse the disposable sleeve

3 The top of the main unit can be turned 360 degrees to both left and right while it is forbidden to remove

4 During operation, the blue light should be aimed straightly at the omposite resin to ensure the effect of solidification

5 Avoid aiming the blue light at eyes directly

6 Please use the power adapter and lithium battery which is designed and supplied by our company. It may cause potential dangers to operator  and patient by using the power adapter and lithium battery which is  designed and supplied by other manufacturers

7 It is forbidden to use metal or other conductors to touch the main Init and the charging point of pedestal because it may burn the internal  circuit or make the lithium battery short circuit

8 Please recharge the battery in cool and ventilated room

9 It is forbidden to self-taking apart the battery, in order not to result in short-circuit or leakage

10 It is forbidden to extrude, shake or rock the battery. The Li-ion battery is  forbidden to be in short-circuit situation and it is forbidden to put the  battery with metal or other conductors

11 To invoid electromagnetic interference, the device should be installed at the medical site which meet the requirement of EMC.

1.WARNING: If the curing light works for 40s continously, the temperature of the top of optical fiber may reach 56C

2.WARNING: Do not modify this equipment without authorization of the manufacturer.

3.WARNING: The adapter should be connected to the socket which is easy for operator to touch

4.WARNING: over-heat scorching: interval time should be no less than

Contraindication:

The heart disease patients, pregnant women and children should be cautious to use this equipment.

Daily maintenance:

1 This equipment does not include the self-maintainable spare parts

The maintenance of this equipment should be taken by the appointed professional or special repair shop

2 Users can change the disposable sleeve and lithium battery. Please use accessory which is designed and supplied by our company, contract  with the local dealer or our company if you want to buy. It may cause  potential dangers to curing light or other damages which is designed and  supplied by other manufacturers

3 The accessory of the product should be cleaned by clean water or neutral sterilized liquid. Do not soak. Do not use highly volatile and  diffluent solvent to clean this equipment, which can cause the signs on  the control pa

4 Please clean the resin remained on the top of the main unit after using to avoid infecting the life-span or solidified effect

5 The device cannot be maintanenced during operation. And it is suggested to maintain it once a month. But sleeve is for one-time usage  and no need for maintanance


 

510(K) Number: K192233
Regulation Number: 21 CFR 872.6070
Product Code: EBZ

 

 

FDA Statement    

The sale of this item may be subject to regulation by the U.S. Food and Drug Administration and state and local regulatory agencies.

If so, you can bid on this item only if you are an authorized purchaser.

If the item is subject to FDA regulation, I will verify your status as an authorized purchaser of this item before shipping of the item.

Feedback

IMPORTANT INFORMATION ON OUR POLICY AND FEEDBACK

  1. Please leave me FIVE STAR POSITIVE  feedback if you are satisfied with our items.  
  2. We try to be fair and accurate with all of our product listings and descriptions. Please read each auction, bid, and sale carefully.
  3. We will appreciate it if you please email us before leaving negative feedback. If there is a problem, we can work together to resolve it. 
    We strive to always be extremely fair and always try to work with reasonable customers.
  4. Negative feedback doesn't go away and should only be left as a last resort! We strive for positive feedback, harmonious relations and even friendships. 
    We will always make every attempt possible to resolve issues if we made a mistake.(It happens). Please do not assume a mistake is intentional.
    Let us know if our service could be better!!

Shipping

  1. International Shipping to worldwide.
  2. Handling within 24 business hours.
  3. Tracking info of your parcel is available.
  4. Returns could be accepted within 30 days after receipt of the item.
  5. Import duties, taxes and charges are not included in the item price or shipping charges. These charges are the buyer's responsibility.Please check with your country's customs office to determine what these additional costs will be prior to bidding/buying.
  6. It usually takes 15-45 business days to arrive by economy international shipping and 7-12 business days by express. The following form is for your reference.

Payment

We accept PayPal payment ONLY, it is easy and safe. Payment should be sent within 7 (SEVEN) days of auction closing. All winning bidders whom won our item, please let me know your contact number after you made the full payment , we need this number to make sure you can receive your item in time, and also for emergency contact consideration.

 

Returns  

  1. Returns could be accepted within 30 days after receipt of the item.
  2. Terms of Sale:
    Refund or replacement request is available only the requests within 1 week after parcel received & returning the item as the same condition as received. Please contact us to request a return authorization. Your name, auction number, and reason for return should be included in the email. All items returned must contain all original packaging materials.Please repack the item carefully. Items returned will be tested and a new replacement will be shipped to the buyer immediately when found defective. In the event that a suitable replacement is not available then a refund will be issued. Shipping, handling and insurance fees are non refundable. If the item is found non-defective, the item will be sent back to the buyer at buyer's expense. Items returned without RMA number will be refused and returned to the sender. Buyer is responsible for All Return Postage and Shipping Charges. Buyer is responsible for additional shipping costs for items that are returned refused and / or undeliverable. We do not accept any returns without an authorization number on the box or label it is being returned

 


Am 11.03.20 hat der Verkäufer die folgenden Angaben hinzugefügt:

 


Am 11.09.2023 hat der Verkäufer die folgenden Angaben hinzugefügt:


Am 08.12.2023 hat der Verkäufer die folgenden Angaben hinzugefügt:


Am 28.03.2024 hat der Verkäufer die folgenden Angaben hinzugefügt:

  • Condition: Neu
  • Item: Curing light T4
  • Marke: Markenlos
  • FDA: K192233
  • Ausgewählte Suchfilter: Polymerisationslampe

PicClick Insights - Zahnaufhellung LED Curing Light Lamp Dental Zahnarzt Polymerisationslampe GYX PicClick Exklusiv

  •  Popularität - 0 Beobachter, 0.0 neue Beobachter pro Tag, 2 days for sale on eBay. 0 verkauft, 30 verfügbar.
  •  Bestpreis -
  •  Verkäufer - 10.606+ artikel verkauft. 0.6% negativ bewertungen. Großer Verkäufer mit sehr gutem positivem Rückgespräch und über 50 Bewertungen.

Die Leute Mochten Auch PicClick Exklusiv