Telemecanique Altivar 31 ATV31HU15N4 1,5kW 2HP 380/500V 0,5-500Hz

Altivar

Variable speed drive

Simple machine

ATV31

With heat sink

Integrated

380...500 V - 5...5 %

50...60 Hz - 5...5 %

3 phases

1.5 kW 4 kHz

2 hp 4 kHz

4.8 A at 500 V 6.4 A at 380 V, Isc = 1 kA

4.2 kVA

1 kA

4.1 A 4 kHz

6.2 A for 60 s

61 W at nominal load

Sensorless flux vector control with PWM type motor control signal Factory set : constant torque

3

Asynchronous motors

323…550 V

47.5...63 Hz

0.0005…0.5 kHz

4 kHz

2...16 kHz adjustable

1…50

150…170 % of nominal motor torque

<= 150 % during 60 s with braking resistor 100 % with braking resistor continuously 150 % without braking resistor

Frequency PI regulator

Adjustable Automatic whatever the load Suppressable

<= power supply voltage

Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6 terminal 2.5 mm² AWG 14 L1, L2, L3, U, V, W, PA, PB, PA/+, PC/- terminal 2.5 mm² AWG 14

Al1, Al2, Al3, AOV, AOC, R1A, R1B, R1C, R2A, R2B, LI1...LI6: 0.6 N.m L1, L2, L3, U, V, W, PA, PB, PA/+, PC/-: 0.8 N.m

Electrical between power and control

Internal supply for logic inputs: 19...30 V 100 mA, protection type: overload and short-circuit protection Internal supply for reference potentiometer (2.2 to 10 kOhm): 10...10.8 V 10 mA, protection type: overload and short-circuit protection

AI3 configurable current 0...20 mA, impedance: 250 Ohm AI1 configurable voltage 0...10 V, input voltage 30 V max, impedance: 30000 Ohm AI2 configurable voltage +/- 10 V, input voltage 30 V max, impedance: 30000 Ohm

LI1...LI6: 4 ms discrete AI1, AI2, AI3: 8 ms analog

AOV, AOC 8 ms for analog R1A, R1B, R1C, R2A, R2B 8 ms for discrete

+/- 0.2 % for output

2

AOC configurable current: 0...20 mA, impedance: 800 Ohm, resolution: 8 bits AOV configurable voltage: 0...10 V, impedance: 470 Ohm, resolution: 8 bits

Positive logic (source) (LI1...LI6), < 5 V (state 0), > 11 V (state 1) Logic input not wired (LI1...LI4), < 13 V (state 1) Negative logic (source) (LI1...LI6), > 19 V (state 0)

2

Configurable relay logic: (R1A, R1B, R1C) 1 NO + 1 NC - 100000 cycles Configurable relay logic: (R2A, R2B) NC - 100000 cycles

R1-R2 10 mA at 5 V DC

R1-R2: 2 A at 250 V AC inductive load, cos phi = 0.4 and L/R = 7 ms R1-R2: 2 A at 30 V DC inductive load, cos phi = 0.4 and L/R = 7 ms R1-R2: 5 A at 250 V AC resistive load, cos phi = 1 and L/R = 0 ms R1-R2: 5 A at 30 V DC resistive load, cos phi = 1 and L/R = 0 ms

6

(LI1...LI6) programmable at 24 V, 0…100 mA for PLC, impedance: 3500 Ohm

S, U or customized Linear adjustable separately from 0.1 to 999.9 s

By DC injection

Input phase breaks: drive Line supply overvoltage and undervoltage safety circuits: drive Line supply phase loss safety function, for three phases supply: drive Motor phase breaks: drive Overcurrent between output phases and earth (on power up only): drive Overheating protection: drive Short-circuit between motor phases: drive Thermal protection: motor

>= 500 mOhm 500 V DC for 1 minute

1 LED (red) for drive voltage Four 7-segment display units for CANopen bus status

5 ms for reference change

Display unit: 0.1 Hz Analog input: 0.1...100 Hz

1 RJ45 for CANopen via VW3 CANTAP2 adaptor 1 RJ45 for Modbus

RS485 multidrop serial link for CANopen via VW3 CANTAP2 adaptor RS485 multidrop serial link for Modbus

RTU for CANopen via VW3 CANTAP2 adaptor RTU for Modbus

10, 20, 50, 125, 250, 500 kbps or 1 Mbps for CANopen via VW3 CANTAP2 adaptor 4800, 9600 or 19200 bps for Modbus

1…127 for CANopen via VW3 CANTAP2 adaptor 1…247 for Modbus

127 for CANopen via VW3 CANTAP2 adaptor 31 for Modbus

CE

Vertical +/- 10 degree

143 x 105 x 150 mm 382 x 239 x 170 mm 184 x 149 x 157 mm

1.8 kg

2410 V DC between earth and power terminals 3400 V AC between control and power terminals

1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5 Electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4 Electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2 Radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3

EN 50178

UL CSA C-Tick N998

On upper part: IP20 (without cover plate) On connection terminals: IP21 On upper part: IP31 On upper part: IP41

2

TC

1 gn (f= 13…150 Hz) conforming to EN/IEC 60068-2-6 1.5 mm (f= 3…13 Hz) conforming to EN/IEC 60068-2-6

15 gn for 11 ms conforming to EN/IEC 60068-2-27

5…95 % without condensation conforming to IEC 60068-2-3 5…95 % without dripping water conforming to IEC 60068-2-3

-25…70 °C

-10…50 °C without derating (with protective cover on top of the drive) -10…60 °C with derating factor (without protective cover on top of the drive)

<= 1000 m without derating >= 1000 m with current derating 1 % per 100 m